"Feature" red and white, red (width: 15CM), white (width: 15CM), with a hexagonal honeycomb pattern on the surface, solid feel, good adhesion, waterproof, strong, long service life and very high luminosity!

Proactive prevention of traffic accidents, particularly, King of embedding traffic accident happened!!

Body reflective logo outlines body contours, improve day and night to identify effects, help identify the number and size of the vehicle and avoid the occurrence of an accident.

1, the best wide angle reflection properties, in the case of large incidence angle can still maintain a good reflective properties.

2, reflective membrane structure flexible, easy to film by hand.

3, surface finish, good resistance to water and humidity, easily gathering dust.

4, wear-resistant, scratch-resistant, high impact resistance to washing, resistant to solvents such as petrol, diesel.

5, using high quality adhesive to make reflective panels combined with solid, easy off, provide excellent durability.

Paste H.1 basic requirements
H.1.1 construction request
body reflective logo should be pasted in the absence of shelter, are easy to see, flat, continuous, and free from dirt, water stains, no grease, no rust, no finish up the body surface.
Paste before pasting wipe dust on the surface of. Parts of the grease stains, stains, use a soft cloth dipped in degreasing solvent or cleaning agent to remove, the dried paste. Has been soft, powder for paint, rust or warping of parts, should remove this part of the paint, sanded antirust treatment on the part of Polish and do, and then paste the body reflective logo.

H.1.2 universal paste request body body reflective logo at the back by the white units started, white end of the unit. Side starting from the red cells, but the last cell near the tail of the vehicle should be white. Paste after body reflective logo, should not affect this standard specifies the performance of vehicle lighting and light signalling devices. Paste after body reflective logo should not be drilled, slotted in the body reflective logo. Body surface when you cannot directly paste body reflective logo, you should paste the body reflective logo has a certain stiffness, strength, ageing resistance of bar, liner, liner paste or firmly riveted bar car. Body reflective logo height from the ground of the minimum 380mm. H.1.3 body reflective logo at the back first, body reflective logo at the back as far as possible reflect the vehicle width and height at the back, horizontal body reflective identify vehicles the back part of the paste width along the edges on either side of the vertical paste after body reflective logo rear high, cargo van rear corner intersection should be white. Three-wheeled car, truck, minivan and part of the rear cargo compartment of the LGV structure does not meet the white cells intersect requests can be red, white cross, but vertical paste the upper part of the unit should be white. Van and trailer van body reflective logo should be reflected in the rear cargo compartment shapes. Secondly, different levels of body reflection marking materials should not be applied to the rear, when the level body reflection marking materials are used, the area of the rear reflector and not less than 0.1m2; when the secondary body reflection marking materials are used, the area of the rear reflector and not less than 0.2m2. Finally, paste body reflective logo at the back should be continuous, not continuous intermittent paste on paste, but each successive length should not be less than 300mm, and red and white body reflective logo should be included at least one unit paste interval should be no larger than 100mm. Under special circumstances, allow the separated red cell and white cell paste, but red, white, and each continuous length should not be less than 150mm, paste interval should be no larger than 100mm. If you are not along the edges on both sides of the rear vertical paste, closest to edge the width of the 50mm surface of the Paste Paste body reflective logo on the top edge as close as possible to the rear edge. H.1.4 side body reflective identifies side body reflective identifies of paste allows interrupted, but its total length (not containing interval part) not should is less than captains of 50%, each continuous paragraph length not should is less than 300mm, and should contains red, and white body reflective identifies at least the a unit, II level body reflective identifies material paste interval not should is greater than 150mm, a level body reflective identifies material paste interval not should is greater than 300mm, paste should as longitudinal uniform distribution. Under special circumstances, allow the separated red cell and white cell paste, but should remain red and white, each continuous length should not be less than 150mm, secondary body reflection marking materials paste interval should be no greater than 150mm, level body reflection marking materials paste interval should be no larger than 300mm. Side body reflective logo on three-wheeled vehicle shall be not less than the length of 1.2m; 50% van cargo compartment length is not long enough for the length of the cargo compartment; side body structure of a continuous surface for concrete mixer trucks and special vehicles, paste it in total length should not be less than length of 30%. Vans and box-type trailer body reflective logo should reflect the cargo compartments on the side of outline. Side body reflection marking materials of level can be different from the rear body reflection marking materials. H.2 three-wheeled vehicle, truck, bar plate ordinary trucks, bar plate semi-trailer paste example Figure H.1 paste example three-wheeled vehicle the side Note: the length of the three-wheeled vehicle side body reflective logo pasted (without gaps) should not be less than 1.2m. Figure H.2 truck side cargo compartment length is less than the length of 50% paste example Note: cargo compartment length of 50% truck is not long enough, the side body reflective logo should be pasted in a row, the length should be cargo compartment length. Figure H.3 bar paste the plate side of the truck and trailer samples Note: in addition to three-wheeled vehicle, cargo compartment length less than length of 50% of truck side body structure, as well as a continuous surface of concrete mixer trucks and special operations vehicle, other trucks and trailers-length body reflective logo on the side (without gaps) shall be not less than bus drivers 50%. Figure H.4 three-wheeled vehicle, truck, bar plate plate semi-trailer rear paste ordinary trucks, bar example Note: three car, and speed truck, and bar plate General truck, and bar plate half trailer Hou Department body reflective identifies of paste reference figure H.4, three car, and speed truck, and part micro truck and light truck Hou Department bar Board height insufficient to paste continuous length for 300mm of body reflective identifies (containing red, and white the 1 a unit) Shi, can only paste long 150mm of white unit. Level when you paste body reflective logo at the back, you should choose fence sites below to paste, to paste, can be pasted on boards or paste on the rear protective devices. Medium and heavy bar plate General truck, and bar plate half trailer should in cab rear fence above sides or cab Hou Department above sides corner with white body reflective identifies mosaic into "pour l", "pour l" level direction length for 300mm (by 2 a length for 150mm of white unit mosaic and into), "pour l" vertical direction length for 350mm (by 2 a length for 150mm of white unit and level direction wide 50mm of white unit mosaic and into). Figure H.4 is the secondary body reflection marking materials paste examples, three-wheeled vehicle, truck, minivan and some light goods vehicles, the rear can be pasted into "-" paste to meet area requirements. Use first-level body reflective logo at the back material, intermittent paste, vertically at the top and the bottom should be pasted horizontally Center far left, far right, and paste each continuous length should not be less than 300mm, and red and white body reflective logo should be included at least one unit for each pasted size should not be less than 0.1m2. H.3 van truck, van ordinary trucks, van semi-trailer paste example Figure H.5 van truck, van ordinary trucks, van semi-trailer paste example Note: the side body reflective logo along the bottom edge of the compartment should be pasted in side compartments on both sides of the upper body reflective logo with white stitching corner "l", "l" horizontally and vertically by 2 white cells spliced into a length of 150mm. Body reflective logo at the back should be sketched out the contours of the rear, four corners should be white. Due to a continuous hinges, locks and other paste, paste allowed intermittent. Figure H.5 b) is the secondary body reflection marking materials paste example, when using the level body reflection marking materials, application white cargo van rear corner unit outline contours, other parts of the intermittent paste, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit. H.4 van paste example Figure H.6 van paste example Note: the total length of the side of the van body reflective logo pasted should meet the captains 50%. Body reflective logo at the back should outline the rear contours, the four corners should be white. Due to a continuous hinges, paste, paste allowed intermittent. Figure H.6 b) is the secondary body reflection marking materials paste example, when using the level body reflection marking materials, application white cargo van rear corner unit outline contours, other parts of the intermittent paste, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit. H.5 warehouse Gate-type trucks, warehouse gate semi-trailer paste example Figure H.7 warehouse Gate-type trucks, warehouse gate semi-trailer paste example Note: body reflective logo at the back should be sketched out the contours of the rear, corner unit should be white. The rear cargo compartment door hinge, door locks not continuous when pasted, paste allowed intermittent. Figure H.7 in the b) is II level body reflective identifies material of paste example, using a level body reflective identifies material Shi, goods van Hou Department corners application white unit outline profile, other parts used intermittent paste, but each continuous paragraph length not should is less than 300mm, and and contains red, and white body reflective identifies at least the a unit, paste area not should below 0.1m2; figure H.7 in the c) is II level body reflective identifies material of paste example, using a level body reflective identifies material Shi, used intermittent paste, Vertically at the top and the bottom should be pasted horizontally Center far left, far right, and should be pasted, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit for each pasted size should not be less than 0.1m2. H.6-dump truck, dump truck paste example a) Paste example b side) rear paste example Figure H.8-dump truck, dump truck paste example Note: paste in addition to board the upper horizontal rear direction, also, paste Board bottom or rear underrun protection device, among other locations. Figure H.8 b) is II level body reflective identifies material of paste example, using a level body reflective identifies material Shi, in ensure reflected vehicles Hou Department width and height of premise Xia, used intermittent paste, vertical direction most above and most below should paste, level direction most left, and most right and middle parts should paste, each continuous paragraph length not should is less than 300mm, and and should contains red, and white body reflective identifies at least the a unit, paste area not should below 0.1m2. H.7 flatbed trucks, flatbed semitrailer, low flat panel semi-trailer, container semi-trailer paste example a) Paste example b side) rear paste example Figure H.9 platform car paste example Note: the Tablet under the side of the truck body reflective logo along the side edge levels of continuous flat surface pasting. Figure H.9 b) is an example of secondary body reflective logo pasted material, if the Tablet cannot be pasted in the back should be level side by side in the rear underrun protection device continuously pasted two body reflective logo, paste size should not be less than 0.2m2. When rear body reflection marking materials using level, the flat-panel or rear underrun protection device on horizontal continuous paste, paste size should not be less than 0.1m2; Figure H.10 flatbed semi-trailer, container semi-trailer paste example Note: the paste side body reflective logo along the side of the frame horizontal, frame structure, body reflective logo pasted on the side is not on the same level. Rear underrun protection device, you should be affixed on the rear underrun protection device. Flat rear and rear underrun protection devices shall be continuous secondary body reflective logo pasted material, when using the level body reflection marking materials, paste the intermittent, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit, paste size should not be less than 0.1m2. Container semi-trailer loaded containers, container should be affixed on body reflective logo, paste style figure H.5. In Figure H.11 low flat panel semi-trailer paste example Note: the side along the frame formed a continuous surface, can be intermittent paste. Frame structure, body reflective logo pasted on the side is not on the same level. Tablet shall be continuous in the back paste the secondary body reflection marking materials, when using the level body reflection marking materials, paste the intermittent, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit, paste size should not be less than 0.1m2. Rear ladder, two ladders ladder rack paste body reflective logo on the outside, at least in the top of the ladder, middle, and bottom paste, but each successive length should not be less than 300mm, and contains a red and white body reflective logo at least one unit. H.8 semi-trailer tank truck, tank paste example Figure H.12 semi-trailer tank truck, tank paste example Note: the tank truck, tank trailer side body reflective logo on the body side of the frame or paste the Center tank level, reflecting the tank length. Irregular side tank semi-trailer body reflective logo pasted on the side of the tank should be centered, reflect length of the tank. Tank body reflective logo outline contour of the tank at the back, the secondary number body reflection marking materials used should be twice times the level body reflection marking materials. Figure H.13 the tank truck transportation of highly toxic chemicals or explosives paste example Note: side body reflective identifies should in body side of frame parts level paste, reflected frame length, and in tank body side with side long for 300mm (2 a 150mm long of unit mosaic) white body reflective identifies mosaic into "l" and "pour l", upper body reflective identifies most Xia along and orange reflective with of distance should in 100mm to 300mm within, lower body reflective identifies most Shang along and orange reflective with of distance should in 100mm to 300mm within, body reflective identifies and tank body Qian, and Back-end the maximum distance should be less than 300mm. White body reflective logo at the back of the tank outline contours, paste the secondary body reflection marking materials at intervals not greater than 50mm, level body reflection marking materials paste intervals should be less than 100mm. H.9 concrete mixer paste example H.14 concrete mixer paste example Note: the side body, concrete mixer truck reflective logo should be pasted parts (such as lateral protection device) for paste, paste the total length can be less than the length of the 50%, but should not be less than the length of the 30% disconnect interval is not restricted. The rear shall be selected to reflect the body back width and height of a continuous plane of paste, such as a rear underrun protection device, metal fenders and other fixed structures. H.10 dedicated job car paste example dedicated job car Shang body reflective identifies of paste should as by Qian said basic paste requirements for paste, part dedicated job car except cab outside of body structure no continuous plane, cannot meet requirements Shi, vehicles Hou Department should as selected can reflected body Hou Department width and height of continuous plane paste, as Hou lower protection device, and metal fender, fixed structure pieces; side body reflective identifies should in can paste parts (as side protection device) continuous paste, Paste the 50% total length can be less than the length of the vehicle, but should not be less than the length of the vehicle 30%, disconnect interval is not restricted. H.15 paste example compression refuse collector Figure H.16 crane paste example H.17 road Sweeper paste example H.18 wrecker paste example H.11 semitrailer tractor paste example H.19 semitrailer tractor paste example Note: half hanging tractor of side without paste body reflective identifies, Hou Department should in cab Hou Department paste, using II level body reflective identifies material Shi, level direction should tied continuous paste 2 row, vertical direction each side should the paste 2 a long 150mm of white unit, paste area not should below 0.2m2; using a level body reflective identifies material Shi, level direction should continuous paste, vertical direction each side should the paste 1 a long 150mm of white unit, paste area not should below 0.1m2.